lock plus

Stockmar beeswax candlemaking set

CAD $178.00
CAD $165.00
(You save CAD $13.00)

100% beeswax, including wick.

The set contains all you need to make your own candles:

- metal cylinder with 1 kg (2.2 lbs) pure beeswax
- additional 1 kg (2.2 lbs) pure beeswax (chips)
- wooden dipping tool 
- 25 candlewicks 16.14 inch length each
- instruction manual

In addition you require 2 bricks (or similar) and a pan with water.

 

To use:

1. You will first prepare a 'double-boiler' for the beeswax pallets, with the included tin being the container to melt the wax, and a large pot of your own to boil water in.  To begin, fill your large stockpot only halfway with water.  Place the tall tin with beeswax pellets inside of the stockpot.  In this manner, there is no water touching the actual beeswax pellets.  Turn the burner to high heat.  The temperature of the water should remain under 200 degrees Fahrenheit.

Hopefully you can keep your pot clean.  It may still happen that some beeswax might drip into your pot.  Some people like to use a pot that they don't worry about dripping wax as much, but it is possible with a careful handling to keep your pot clean, and the beeswax contained to the tin. 

2.  As the wax is melting, you can prepare the candle wick.  You can make just one candle at a time, or you can use a longer string holding it in the middle with both ends dipping in at the same time to make two candles at once.  It may be helpful to tie little weights to the ends of the string; you might use hex nuts, fishing weights, pennies stuck together in a clump of soft wax.  If you do two candles at a time, then hanging them to dry afterwards will be easier for candles that are thicker diameter and need more time to dry.  If you are only making very small diameter candles, then they won't take long to dry, and doing one candle at a time is fine.

3.  Test the wax temperature with the included thermometer.  It should be 165 degrees Fahrenheit. 

4.  You're ready to begin.  For your first dip of the wick, you will seal the wick by dipping it into the melted wax to the desired length of the candle.  Lift back out again into the air.

5.  The wax should take about 4 seconds or so to air harden once the wick is lifted out of the melted wax.  Re-dip once more, and then immediately plunge into cold water bath.  Repeat Steps 4 & 5 until your candle reaches the desired diameter.

6.  For some old-fashioned charm, hang the finished candles over a broom balanced on two chair backs, making sure the candles don't touch each other. Leave them to harden for a day in a cool, draft-free spot.  Cut off the weights, and re-dip the ends to have the bottoms be more tapered.

Note: The beeswaxes pellets reduce in volume when melted.  We advise you to keep a refill bag with beeswax pellets from Dipam, or simply melt down your remnants from your old beeswax candles.

Made in Germany by Stockmar.

Read more
Current stock 1

Description

100% beeswax, including wick.

The set contains all you need to make your own candles:

- metal cylinder with 1 kg (2.2 lbs) pure beeswax
- additional 1 kg (2.2 lbs) pure beeswax (chips)
- wooden dipping tool 
- 25 candlewicks 16.14 inch length each
- instruction manual

In addition you require 2 bricks (or similar) and a pan with water.

 

To use:

1. You will first prepare a 'double-boiler' for the beeswax pallets, with the included tin being the container to melt the wax, and a large pot of your own to boil water in.  To begin, fill your large stockpot only halfway with water.  Place the tall tin with beeswax pellets inside of the stockpot.  In this manner, there is no water touching the actual beeswax pellets.  Turn the burner to high heat.  The temperature of the water should remain under 200 degrees Fahrenheit.

Hopefully you can keep your pot clean.  It may still happen that some beeswax might drip into your pot.  Some people like to use a pot that they don't worry about dripping wax as much, but it is possible with a careful handling to keep your pot clean, and the beeswax contained to the tin. 

2.  As the wax is melting, you can prepare the candle wick.  You can make just one candle at a time, or you can use a longer string holding it in the middle with both ends dipping in at the same time to make two candles at once.  It may be helpful to tie little weights to the ends of the string; you might use hex nuts, fishing weights, pennies stuck together in a clump of soft wax.  If you do two candles at a time, then hanging them to dry afterwards will be easier for candles that are thicker diameter and need more time to dry.  If you are only making very small diameter candles, then they won't take long to dry, and doing one candle at a time is fine.

3.  Test the wax temperature with the included thermometer.  It should be 165 degrees Fahrenheit. 

4.  You're ready to begin.  For your first dip of the wick, you will seal the wick by dipping it into the melted wax to the desired length of the candle.  Lift back out again into the air.

5.  The wax should take about 4 seconds or so to air harden once the wick is lifted out of the melted wax.  Re-dip once more, and then immediately plunge into cold water bath.  Repeat Steps 4 & 5 until your candle reaches the desired diameter.

6.  For some old-fashioned charm, hang the finished candles over a broom balanced on two chair backs, making sure the candles don't touch each other. Leave them to harden for a day in a cool, draft-free spot.  Cut off the weights, and re-dip the ends to have the bottoms be more tapered.

Note: The beeswaxes pellets reduce in volume when melted.  We advise you to keep a refill bag with beeswax pellets from Dipam, or simply melt down your remnants from your old beeswax candles.

Made in Germany by Stockmar.

Reviews (0)

Be the first to write a review

Additional info

SKU: MER 85075500